Posts Tagged ‘Moreland Hills’

Kingsville Heat Pump Tip: Ice and Snow Covered Heat Pump

Wednesday, January 18th, 2012

It’s very common for heat pumps in Kingsville to ice over in the winter time. It can be due to freezing temperatures and icing outside or it could be due to constant running of the heat pump or excess moisture on the coils. However, while a bit of ice on the heat pump is relatively normal, the entire unit should never be covered in ice – such a thing is not only hard on the machinery; it can result in no heat for your home.

How to Handle Ice and Snow on the Heat Pump

Should your heat pump become covered in ice or snow in the winter time, there are a few things you can do and some things you should not do. First, check to make sure the problem isn’t related to a broken defrost cycle timer. The heat pump should go into a defrost cycle every 30-90 minutes to keep excess ice from building up. If this doesn’t happen, it should be inspected for a thermostat or sensor problem.

To actually remove the ice from the unit, never use a sharp object to pick the ice clear. You can easily damage the coils or another part of the unit and leave it permanently broken. The best way to remove ice from your heat pump is to rinse it off with a hose – even cold water will remove ice. Just be sure the defrost cycle is ready to come back on so the water used to rinse away the ice doesn’t freeze.

Remember to check your emergency heating source and make sure it is switched on while this is happening. Your heat pump likely won’t work properly while iced over and if it is left in the on position, excess stress on the device will cause damage.

To avoid this kind of damage, turn off the heat pump and turn on your emergency heating source, then clear away the ice and check the defrost timer. If everything works properly, turn the heat pump back on, but if you find any problems, call a professional to do a more thorough inspection of the device before you use it again.

Tags: , , , , , ,
Posted in Heat Pumps | Comments Off

Downflow Gas Furnace Tips from South Russell

Wednesday, December 28th, 2011

Proper care of a downflow gas furnace starts with proper installation and continues through routine cleaning and maintenance. But before you can even have a downflow gas furnace installed, you need to make sure it’s the right fit for your South Russell home.

Downflow gas furnaces are so named because of the direction that air flows through them. The cooler air is taken in at the top and directed downward, heating up as it travels, and then is expelled through the bottom of the furnace into ducts that feed the rest of the house. Because of this configuration, downflow  gas furnaces are typically installed in attics as opposed to basements.

If you have a basement and you’d rather install your furnace there, then an upflow furnace is probably the better choice for you. However, as many newer homes don’t have basements at all, downflow gas furnaces are growing in popularity and usefulness.

As with any other furnace, it’s important to have a downflow gas furnace professionally installed. This will ensure that the venting system is properly in place and that your house will be heated as effectively and efficiently as possible.

Of course, there are some other things you can do to help your furnace heat your home and keep your energy bills down. For instance, make sure you have proper insulation everywhere, particularly in the attic and crawlspaces where much of the normal heat loss in a home occurs.

You can also make your home more airtight in the winter by sealing up any unused windows and doors with plastic and making sure all storm windows are in place. Basically anyplace that a draft could develop, you could be losing heat and that costs you money. So to ensure that all of the money you’re spending to heat your house is actually going to that purpose, check periodically to make sure your home is still sealed up tight.

Also, just like any other type of furnace, a downflow gas furnace will require regular maintenance to make sure it continues to run efficiently and to replace any parts that may have worn out over time. Having a South Russell professional technician come out once a year to carry out this type of service will wind up saving you a bunch of money and can help catch problems before they are able to get out of hand.

Tags: , , , , ,
Posted in Heating | Comments Off

A Question from Kirtland Hills: Why Does My Furnace’s Pilot Light Keep Going Off?

Monday, December 5th, 2011

If you have an older furnace with a gas pilot light and it keeps going out, heating your Kirtland Hills home can become a frustrating process. Not only are you forced to trudge downstairs to light it every time you need heat, but you’re probably starting to worry that there is something wrong – either with your furnace or with your gas supply. Here are some possible reasons for your pilot light shutting off and what you can do about them.

  • Thermocouple – The thermocouple is used to generate electricity from the gas being burned by the pilot light to power the sensor that keeps the pilot light running. So, if the thermocouple goes bad or gets blocked in some way, the sensor won’t work properly and your pilot light won’t remain lit. Even a small problem with the thermocouple can lead to the valve closing and the pilot light going out.
  • Gas Pressure – If the gas pressure going to your furnace is too low, due to a leak, pipe problem or another appliance, the pilot light may not have enough gas to stay lit. While it is possible that the problem is not related to gas pressure, anything that affects the flow of gas into your home should be inspected by a professional. If you smell gas, leave the house and call your gas company immediately.
  • Mercury Sensor – The sensor in your pilot light that maintains the flow of gas to keep it lit can go bad. Keep in mind that these sensors almost always used to contain mercury (and often still do), so you should be careful with them. It’s best to call a professional who can replace and dispose of it properly.
  • Dirty Burners – Excess dust, lint, rust or sulfur build up can result in blockage of the burner holes. When this happens, gas will flood into the chamber but not light right away. When it does finally light, it will create a small boom or banging sound that will often put out the pilot light. Not only is this inconvenient, it is very dangerous. Fortunately, it can be avoided with annual cleanings of your furnace.

The best way to keep your pilot light lit at all times is to have someone inspect it once a year. If something happens in between, you can usually rule out cleanliness issues and call in a professional to check the thermocouple and sensor.

Tags: , , , , ,
Posted in Heating | Comments Off

It’s Time for a New Furnace: Some Advice From Euclid

Wednesday, October 5th, 2011

Replacing your Euclid home’s furnace is probably not something you want to think about. After all, a new furnace is a big investment and not something you probably have too much experience with. And sometimes having your current system fixed or tuned up is all you need to get your home heating situation back on track. But there are certain situations in which it makes more sense to just go ahead and get a new furnace rather than simply patching up the old one.

For instance, if you have to call for either minor or major repairs to your furnace on a regular basis, it’s probably time to consider investing in a replacement. All of those repairs cost money and chances are that the furnace you’re paying repeatedly to replace isn’t going to last that much longer anyway.

Rather than continuing to dump money into a furnace that just isn’t cutting it anymore, you’ll be better off making the investment in a new unit. The truth is, you’re going to have to do it sooner or later and by buying a new furnace now, you’re actually saving all of the money you would have spent on repairing the old one for another year or so.

Also, a furnace that requires such frequent repairs is probably not functioning all that efficiently either. When you replace it with a newer model, you won’t just save money on repairs. You’ll also likely notice a considerable savings on your monthly energy bills because of how much more efficient your new model is.

Even if you haven’t been repairing your furnace often, you may be able to notice some signs that the old unit isn’t quite up to the task anymore. If you’re suddenly having some significant humidity problems in your house or if your home isn’t being heated evenly, there’s a good chance your furnace is on its way out.

And, in fact, even if your furnace is functioning just fine but is more than 10 years old or so, it’s very likely you’d benefit by replacing it. That’s because the newer furnaces available now are so much more energy efficient than their predecessors that the savings you’ll incur monthly will quickly make up for the initial installation investment.

Of course, you don’t want to get rid of a good furnace if you don’t have to. But if your furnace is getting close to the end of its expected lifespan, you may very well benefit by putting out the money for a new one now so you can start saving right away on your monthly energy bills.

Tags: , , , ,
Posted in Heating | Comments Off

IAQ – Filters

Wednesday, June 29th, 2011

Installing air filters in your home is a great way to make sure the air your family breathes every day is safe and free of contaminants. But you shouldn’t just go out and buy the first air filter you see. When it comes to quality air filtration, HEPA filters are the industry leaders, and for good reason. They can remove up to 99.97% of indoor air contaminants that measure 0.3 microns or larger, a phenomenal success rate unmatched by any other filters on the market.

Proper HEPA Filter Practices

To be effective, even HEPA filters need to be installed and maintained properly. Consulting with an HVAC professional is the best way to ensure that the air filtration system you get is completely compatible with your home heating and cooling system. The filter must also be installed in the appropriate place so it can catch the most contaminants. Especially if you have a forced air heating and cooling system, there are a lot of potential locations for your filters. A good HVAC professional can help you determine which spots will serve you best.

Changing Your HEPA Filters

Once your filtration system is in place, you should maintain it properly so it continues to catch and remove all those unwanted particles from your indoor air. Keeping up with the proper filter changing schedule is a big part of this. Every HEPA filter comes with manufacturer’s recommendations on how often the filter needs to be changed. Prefilters often need to be changed more often, sometimes even once every 90 days, so you should find out if your system has one of these as well.

Many HEPA filters only need to be changed once every year or two, but the conditions in your home can make it necessary to change them more often. For example, if your home has a lot of dust or other specific air contaminants, you may need to change your HEPA filter as often as once a year.

Both HEPA filters and prefilters are quite easy to remove and replace. If you’re not sure how to do it, have your technician show you the next time they come out for a routine maintenance visit or when they put install the system. As long as you replace your filters regularly, you should have no trouble maintaining high indoor air quality with a HEPA air filtration system.

Tags: , , ,
Posted in Indoor Air Quality | Comments Off

What Are Limit Switches and How Do They Work?

Monday, May 30th, 2011

When you set the thermostat on your air conditioning system, you pretty take for granted that the system will maintain that temperature throughout your house. But did you ever stop to think about how it’s actually accomplished? The truth is that there are many moving parts that all play a role in keeping your home cool and comfortable, and one of these is the limit switch.

What Is a Limit Switch?

Although you’re probably not aware of it, you’ve encountered plenty of limit switches over the years. A limit switch is anything that stops an electric appliance under certain circumstances. The little switch that turns the light on in the refrigerator when you open the door and then off again when you close it is the perfect example of a limit switch. Another common one is the switch that stops your washer or dryer from running when you open the door. Limit switches are used for a variety of appliances and gadgets to not only save electricity but to keep you and your device safe.

Limit Switches and Air Conditioning

The limit switch on your air conditioning system is the link between the blower on your air handler and the thermostat. When the thermostat senses that the desired indoor temperature has been reached, it stops the air conditioner from producing any more cold air. At that point, it’s important for the blower to stop functioning as well.

If it doesn’t, the blower will continue to move and warm air rather than cold will begin circulating throughout your home. However, if the blower shuts off too soon, the cold air that’s still being generated by the air conditioner won’t be able to circulate. So it’s essential that the blower be switched off at the same time the cold air stops arriving. That’s exactly what the limit switch does.

While it’s only one very small part of a large machine, the limit switch in your air conditioner plays a vital role in keeping your home comfortable and in allowing your air conditioning system to function as efficiently as possible.

If you notice that your air conditioner is shutting off too soon or not soon enough, it may be because of a broken limit switch. Sometimes, the system simply needs to be reset, something you can do with the help of your owner’s manual. However, if your limit switch is broken, you should contact a professional to take a look and determine if it needs to be replaced.

Tags: , , ,
Posted in Air Conditioning | Comments Off

How Do I Reduce Dust in My Home?

Monday, April 11th, 2011

Dust is everywhere. There is no way to stop it from occurring, so instead we turn to cleaning and filtration to keep the amount of dust circulating through the air to a minimum. Luckily, there are quite a few things you can do, even without installing new equipment, to reduce your dust levels.

Duct Cleaning

First on the list is regular duct cleaning. You dust your furniture and your floors, so why not clean out your ductwork? Properly cleaned ductwork is very important because of just how much stuff can build up in there over time. Imagine regular air flow in an enclosed space that never gets cleaned. How much dust and debris do you think could build up over the course of a year? Hint: it’s enough to keep a steady flow of dust in your indoor air.

Professional duct cleaning is important and should be done once every year or two depending on how often you use your home comfort system. However, you should also clean in and around the vents and ducts in your home where you can reach. This can be done weekly and will help immensely to reduce dust.

Filtration

Most air filters equipped with high quality HEPA filters work extremely well to remove dust from the air. Because HEPA filters can capture particles as small as 0.3 microns, they won’t just remove dust, but pollen, pet dander and even mold. Mold especially is a problem that occurs in far greater frequency in homes without filtration.

Simple air filtration is an affordable solution to a lot of different contaminants, so it’s a good fit for any home. However, there are more powerful systems as well that will reduce both dust and pathogens like bacteria – these purifiers use ionization to draw particles from the air electronically.

Humidity

Humidity imbalance can cause dust problems as well. Low humidity leads to more dead skin and dust in the house, while high humidity causes the development of dust mites. Properly regulating your humidity to slightly less than 50% will create a perfect environment in which less dust is created and circulated in your home.

The best way to reduce dust is to take a three pronged approach to indoor air quality. Cleanliness is always first on the list, but after that don’t neglect the value of filtration and proper humidity control. When used properly, these three things will ensure dust never bothers you again.

Tags:
Posted in Indoor Air Quality | Comments Off